After disconnecting then reconnecting the battery negative cable, reset some parts that require the reset procedures.
(Refer to Body Electrical System – "General Information")
Battery
1.
Turn ignition switch OFF.
2.
Remove the air duct (A).
3.
Disconnect the battery negative (-) terminal (A).
Battery negative (-) terminal tightening nut:
4.0 ~ 6.0 N.m (0.4 ~ 0.6 kgf.m, 3.0 ~ 4.4 lb-ft)
4.
Disconnect the battery positive (+) terminal (A).
Battery negative (-) terminal tightening nut:
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.2 ~ 8.7 lb-ft)
5.
Remove the insulation pad.
6.
Remove the battery mounting bracket (B) after loosening the mounting bolt (A).
7.
Remove the battery.
Battery Tray
1.
Remove the battery tray.
(Reter to Engine Electrical System - "Battery")
2.
Remove the air cleaner mounting bolts (A).
Air cleaner mounting bolt:
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.2 ~ 8.7 lb-ft)
3.
Remove the battery tray (A) after loosening the mounting bolts
Battery tray mounting bolt:
8.8 ~13.7 N.m (0.9 ~1.4 kgf.m, 6.5 ~10.1 lb-ft)
Installation
1.
Install in the reverse order of removal.
•
When installing the battery, fix the mounting bracket on the tray correctly.
•
After disconnecting then reconnecting the battery negative cable, reset some parts that require the reset procedures.
(Refer to Body Electrical System – "General Information")
Inspection
Battery Voltage and Status
Check the battery voltage and status using the battery tester.
Battery Terminal
1.
Move back and forth to check if the battery terminals (A) are loose or corroded. If the terminals are corroded, clean them.
If battery positive connection is loose, disconnect
ground(GND) cable first before attempting to remove or tighten plus
connection, to prevent personal injury.
2.
If the battery clamp on battery positive (+) terminal is not seated securely:
(1)
Turn ignition switch OFF and disconnect the battery negative (-) terminal.
(2)
Tighten battery clamp (A) on battery positive (+) terminal
Battery positive (+) terminal:
7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)
3.
If the battery clamp on battery negative (-) terminal is not seated securely:
(1)
Tighten battery clamp (A) on battery negative (-) terminal.
Battery negative (-) terminal:
4.0 ~ 6.0 N.m (0.4 ~ 0.6 kgf.m, 3.0 ~ 4.4 lb-ft)
Battery Condition
Check the battery for damage or deformation. If severe damage, deformation or leakage is found, replace the battery.
Vehicle parasitic current inspection
[Using the Ammeter]
1.
Turn the all electric devices OFF, and then turn the ignition switch OFF.
2.
Close all doors except the engine hood, and then lock all doors.
(1)
Disconnect the hood switch connector.
(2)
Close the trunk lid.
(3)
Close the doors or remove the door switches.
3.
Wait for a few minutes until the vehicle’s electrical systems go to sleep mode.
•
For an accurate measurement of a vehicle parasitic current,
all electrical systems should go to sleep mode. (It takes at least one
hour or at most one day.) However, an approximate vehicle parasitic
current can be measured after 10~20 minutes.
4.
Connect an ammeter in series between the battery (-) terminal
and the ground cable, and then disconnect the clamp from the battery
(-) terminal slowly.
•
Be careful that the lead wires of an ammeter do not come off
from the battery (-) terminal and the ground cable to prevent the
battery from being reset. In case the battery is reset, connect the
battery cable again, and then start the engine or turn the ignition
switch ON for more than 10 sec. Repeat the procedure from No. 1.
To prevent the battery from being reset during the inspection,
1)
Connect a jump cable between the battery (-) terminal and the ground cable.
2)
Disconnect the ground cable from the battery (-) terminal.
3)
Connect an ammeter between the battery (-) terminal and the ground cable.
4)
After disconnecting the jump cable, read the current value of the ammeter.
5.
Read the current value of the ammeter.
•
If the parasitic current is over the limit value, search for
abnormal circuit by removing the fuses one by one and checking for
parasitic current.
•
Reconnect only the fuse suspected of parasitic current and
search for the trouble unit by removing the components connected to the
circuit one by one until the parasitic draw drops below limit value.
Limit value (after 10~20 min.) : Below 50mA
[Using the Clamp type Ammeter]
1.
Turn the all electric devices OFF, and then turn the ignition switch OFF.
2.
Close all doors except the engine hood, and then lock all doors.
(1)
Disconnect the hood switch connector.
(2)
Close the trunk lid.
(3)
Close the doors or remove the door switches.
3.
Wait for a few minutes until the vehicle’s electrical systems go to sleep mode.
•
For an accurate measurement of a vehicle parasitic current,
all electrical systems should go to sleep mode. (It takes at least one
hour or at most one day.) However, an approximate vehicle parasitic
current can be measured after 10~20 minutes.
4.
Install the clamp type ammerter on battery negative (-) terminal.
5.
Read the current value of the ammeter.
•
If the parasitic current is over the limit value, search for
abnormal circuit by removing the fuses one by one and checking for
parasitic current.
•
Reconnect only the fuse suspected of parasitic current and
search for the trouble unit by removing the components connected to the
circuit one by one until the parasitic draw drops below limit value.
Limit value (after 10~20 min.) : Below 50mA
Cleaning
1.
Make sure that the ignition switch and all accessories are in the OFF position.
2.
Disconnect the battery cables (negative first).
3.
Remove the battery from the vehicle.
•
Care should be taken in the event the battery case is cracked or leaking, to protect your skin from the electrolyte.
Heavy rubber gloves (not the household type) should be wore when removing the battery.
4.
Inspect the battery tray for damage caused by the loss of
electrolyte. If acid damage is present, it will be necessary to clean
the area with a solution of clean warm water and baking soda. Scrub the
area with a stiff brush and wipe off with a cloth moistened with
baking soda and water.
5.
Clean the top of the battery with the same solution as described above.
6.
Inspect the battery case and cover for cracks. If cracks are present, the battery must be replaced.
7.
Clean the battery posts with a suitable battery post tool.
8.
Clean the inside surface of the terminal clamps with a
suitable battery cleaning tool. Replace damaged or frayed cables and
broken terminal clamps.
9.
Install the battery in the vehicle.
10.
Connect the cable terminals to the battery post, making sure tops of the terminals are flush with the tops of the posts .
11.
Tighten the terminal nuts securely.
12.
Coat all connections with light mineral grease after tightening.
•
When batteries are being charged, an explosive gas forms
beneath the cover of each cell. Do not smoke near batteries
being charged or which have recently been charged. Do not break live
circuit at the terminals of batteries being charged.
A spark will occur when the circuit is broken. Keep open flames away from battery.
Description
1.
The CMF(Closed Maintenance Free) battery is, as the name
implies, totally maintenance free and has no removable battery cell
caps.
2.
The CMF(Closed Maintenance Free) batter ...
Tailgate unlocking
Using the tailgate handle button
1. Carry the smart key.
2. Press the tailgate handle button.
3. When all doors are locked, the hazard warning lights will blink two times.
Once the tailgate is ope ...
Rear Stabilizer Bar Repair procedures
Removal
1.
Remove the rear wheel and tire (A) from rear hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)
Be careful not to damage ...
Kia Sedona: Battery Repair procedures
Battery Description and Operation
Battery Troubleshooting