Kia Optima Manuals

Kia Sedona: Instrument Cluster Repair procedures - Indicators And Gauges - Body Electrical System - Kia Sedona YP Service ManualKia Sedona: Instrument Cluster Repair procedures

Third generation YP (2014-2024) / Kia Sedona YP Service Manual / Body Electrical System / Indicators And Gauges / Instrument Cluster Repair procedures

Removal
1.
Disconnect the negative (-) battery terminal.
2.
Remove the center fascia upper panel.
(Refer to Body - "Center Fascia Panel")
3.
Remove the instrument cluster (A) after loosening the screws.

4.
Disconnect the cluster connector (A).

Installation
1.
Connect the cluster connector.
2.
Install the instrument cluster.
3.
Install the center fascia upper panel.
4.
Connect the negative (-) battery terminal.
   
Perform variant coding after exchanging the instrument cluster.
Inspection
1.
Check point (Warning indicator)
No.
Ref Symbol
Name
Color
Signal input
Signal Control(Unit / Sensor)
Check point
1

Turnsignal
Lamp (Left)
Green
CAN
BCM
(Gateway)
CAN line failure
2

Turnsignal
Lamp (Right)
Green
CAN
BCM
(Gateway)
CAN line failure
3

Tail Lamp
Green
CAN
BCM
(Gateway)
CAN line failure
4

Front Fog Lamp
Green
CAN
BCM
(Gateway)
CAN line failure
5

High Beam
Blue
CAN
BCM
(Gateway)
CAN line failure
6

Warning
Yellow
CAN
BSD
TPMS
SCC
LDWS
FCW
HBA
BCM
BSD failure
TPMS failure
SCC failure
LDWS failure
FCW failure
HBA failure
Wiring failure
Hard-wired
Low Washer
(Digital Input)
Washer low
7

Battery Charge
Red
Hard-wired
Alternator
Wiring failure
8

Oil Pressure
Red
Hard-wired
EMS
Wiring failure
9

Check Engine
Yellow
CAN
EMS
CAN line failure
10

Immobilizer
Yellow
CAN
+
Hard-wired
IMMOBILIZER
SMK
CAN line failure+
Wiring failure
11

Parking Brake
Brake Fluid
EBD
EPB
EVP
Red
CAN
BCM
(Gateway)
EBD
EPB
EVP
ABS
TCS
CAN line failure
12

ABS
Yellow
CAN
ABS
CAN line failure
13

ESC
Yellow
CAN
TCS
CAN line failure
14

ESC Off
Yellow
CAN
TCS
CAN line failure
15

EPB
Yellow
CAN
EPB
CAN line failure
16

Auto Hold
White
CAN
TCS
CAN line failure

Green

Yellow
17

Seat belt
Red
CAN
BCM
(Gateway)
CAN line failure
18

Air bag
Red
CAN
ACU
CAN line failure
19

EPS
(MDPS)
Red
CAN
MDPS
CAN line failure
20

TPMS
Yellow
CAN
TPMS
CAN line failure
21

LDWS
Green
Yellow
White
CAN
LDWS
CAN line failure
22

Fuel Low
Yellow
Direct
(Micom)
Fuel Sender
Fuel Sender failure
23

Door Open
Red
CAN
BCM
(Gateway)
CAN line failure
24

Trunk Open
Yellow
CAN
BCM
(Gateway)
CAN line failure
25

ECO
Green
Hard-wired
Eco Mode
Switch failure
26

CRUISE
Green
CAN
EMS
CAN line failure
27

SET
Green
CAN
EMS
CAN line failure
28

HBA
GreenYellow
CAN
LDWS
CAN line failure
29

Glow
Yellow
CAN
EMS
CAN line failure

2.
Check point (Gauge)
NO
Name
Signal Input
Signal Control
(Unit/Sensor)
Check Point
1
Speedometer
C-CAN
ABS/ESC
1) CAN Line failure
3
Tachometer
C-CAN
EMS
1) CAN Line failure
4
Cooling water temperature
C-CAN
EMS
1) CAN Line failure
5
Fuel
Hardwire
Fuel Sender
1) Fuel sender failure
2) Wiring failure
6
Shift lever indicator
C-CAN
TCU
1) CAN Line failure
7
Compass
MM-CAN
HU
1) CAN Line failure
8
Outside temperature
C-CAN
DATC
1) CAN Line failure

Diagnosis with GDS
1.
The body electrical system can be quickly diagnosed for faulty parts using vehicle diagnostic system (GDS).
The diagnostic system (GDS) provides the following information:
(1)
Self diagnosis : Checking the failure code (DTC) and display
(2)
Current data : Checking the system input/output data state
(3)
Actuator test : Checking the system operation condition
(4)
Additional function : Other controlling such as he system option and zero point adjustment
2.
Select the ''Car model'' and the system to be checked in order to check the vehicle with the tester.
3.
Select the ''Body Control Module (BCM)'' to check the ''Cluster Module (CLU)''.
4.
Select the ''Current Data" menu to search the current state of the input/output data.
The input/output data for the sensors corresponding to the cluster module (CLU) can be checked.

5.
To check the input value of cluster illumination, select option "Actuation test".

CLU Variant Coding
After replacing the cluster with a new one, the "Variant Coding" procedure must be performed.
1.
Connect the cable of GDS to the data link connector in driver side crash pad lower panel, turn the power on GDS.
2.
Select model and "BCM".
3.
Select Variant coding mode to perform.

4.
If the trouble codes occurred when performing variant coding, try the CLU variant coding again after checking the installation status of CLU system.

Instrument Cluster Description and Operation
Description Communication Network Diagram AbbreviationExplanationACUAirbag Control UnitADMAssist Door ModuleB_CANBody Controller Area NetworkBCMBody Control ModuleBSDBlind Spot DetectionC_CANCha ...

Troubleshooting
Troubleshooting Error ItemFailure symptomInspection items Detailed inspections Relevant Parts/ComponentsScreen displayTFT-LCD screen does not turn on 1) Connector attachments 2) Components ...

Other Information:

Special Service Tools
Special Service Tools Tool (Number and name)IllustrationUse09977-3R000Disc & hub assembly bolt removerRemoval and installation of disc & hub assembly. ...

Crash Pad Center Panel Components and Components Location
Component Location 1. Crash pad center lower panel ...

Categories


Copyright В© www.kisedona.com 2016-2024